Solid wood door often stainless steel material for general T type, U type and flat three, which ingeneral Home Furnishing building materials market in metal materials or decorative materialplace to buy, but also buy in some building materials hardware stores, but the type and quality is usually better than Home Furnishing market merchants sent a lot.
1, T type stainless steel strip is the most common, when installing the first measured by vernier caliper type T barb parts of the width, and then use a small manual trimming machine or routeron the wooden door to install the stainless strip local milling groove, groove depth is slightly longer than the barb length about 2mm, the width is smaller than the width of the barb 1mm-1.05mm. In the slot coating strong glue, glue quantity should be the stainless strip in a very fewoverflow after the best. The hacksaw saw the stainless strip length to the length you want, pay attention to a section with as much as possible to pick straight, use file trimming, then put intostainless strip slot, lightly with a rubber hammer tamping, the strong glue with gasoline wipe, and then the pressure on the weight and let rest for 2 hours. If the paint doors and paint surface is done, can't use petrol. If you are only strong plastic, it must be less Tu, cannot let the strong adhesive overflow. Can also be replaced by month latex or puzzle glue, wipe glue after heavypressure for 5 hours, but the effect is not as good as strong glue. Is not recommended in the paint surface do with stainless strip.
2, U type and flat stainless: these two kinds of truth and type T stainless strip similar, just the groove width and stainless equal to or slightly larger 1mm, depth and the same stainless material thickness, with strong glue doing before paint adhesion. Type U to fill the square woodof the same size and in the mouth of a U type in the type U and with strong glue fixed. Strong adhesive double coated, hanging out for a while and then stick. Finally, with a rubber hammertight upper to pad have shock protection wood side when hit, to prevent surface damage.
实木门上经常用不锈钢材一般有T型、U型和平板三种，一般在家居建材市场中专售金属建材或者装饰材料的地方能买到，在一些五金建材商店也买到，不过种类和品质通常要比家居市场中的商家差好多。
1、T型不锈条是最常见的，安装时先用游标卡尺测量T型倒刺部位的宽度，然后用小型手动修边机或者镂铣机在木门上要安装不锈条的地方铣槽，槽深略长于倒刺长度2mm左右，宽度小于倒刺宽度1mm-1.05mm。在槽内涂大力胶，胶量应该是把不锈条放入后有极少量溢出最好。用钢锯把不锈条长度锯到你想要的长度，注意尽量挑平直的一段用，用锉修边，然后把不锈条放到槽里，用橡胶锤轻轻砸紧，用汽油把大力胶擦净，然后压上重物静放2个小时。如果是油漆门并且油漆面已经做好，就不能用汽油了。要是你只有大力胶，那就一定要少涂，不能让大力胶外溢。也可以用月乳胶或者拼板胶代替，擦净胶后压重物放5个小时，不过效果不如大力胶。还是不推荐在油漆表面做好后镶不锈条。
2、U型和平板不锈条：这两种道理与T型不锈条类似，只是开槽宽度要与不锈条相等或者略大1mm，深度与不锈材厚度相同，在做油漆前用大力胶粘合。U型条要在U型里填一条与U型内口同尺寸的木方并用大力胶固定。大力胶双面涂，晾一会再粘。最后用橡胶锤砸紧，砸的时候上边要垫有减震保护的木方，防止表面受损。